Description

The C.Scope SGA4 is an affordable Signal Generator designed for use alongside a CXL4 or DXL4 Cable Avoidance Tool. It enables significantly more underground utilities to be detected including street lighting cables.

SIMULTANEOUS DUAL-FREQUENCY
The simultaneous dual-frequency 33kHz and 131kHz signal output of the Signal Generators is ideal for maximising the number of buried services that can be energised and then detected.

The SGA4 Signal Generator can apply the dual frequency signal without direct connection to buried services, using either a Signal Clamp or the simple induction method from ground level, providing a significant improvement in the detection of the smaller diameter or poorly earthed cables.

THREE SIGNAL APPLICATION TECHNIQUES
The SGA4 offers three alternative ways to apply a Signal Generator signal:

Direct Connection allows specific pipes or cables to be individually traced, identified and their depths measured. The use of Signal Clamps, Signal Injectors and Direct Connection leads make this mode the most effective method for pinpointing pipes and cables.

If it is difficult or inconvenient to use Direct Connection, then the Wraparound technique can be utilised to successfully energise a street or car park lighting cable.

Induction allows the Signal Generator to induce a detectable and traceable signal to previously unknown, undetected or inaccessible underground metal pipes or cables.

HIGH POWER SIGNAL
The fully adjustable One Watt Power Output of the SGA4 means that deeper and less conducting pipes and cables can be effectively energised and then traced over ever longer distances.

It also features a two position power levels so the operator has some control of how much power is in use and when.

PULSED/CONTINUOUS SIGNAL OUTPUT
A Pulsed or Continuous signal output allows operators to switch to the Pulsed Mode at the push of a button in high interference situations and keep on tracing. The SGA4 has a clear audible signal output to indicate when it is in operation.

A useful in-built audio mute control is also included.

ROBUST AND DURABLE CONSTRUCTION
The SGA4s twin wall construction is robust and durable. It also provides IP65 standard protection against dust and water ingress.

ACCESSORY TRAY
The SGA4 Signal Generator has a large detachable accessory tray as its base. It can house not only the standard accessories (Direct Connection Leads, Earth Stake, Connection Magnets, 10m Auxiliary Earth Lead) and the Instruction Manual but also many of the optional extras such as Signal Clamps, Sondes and Signal Injectors.

THREE YEAR WARRANTY
The SGA4 comes with a three year Warranty (conditions apply).

Overview

• One Watt High/Low Power Output
• Simultaneous 33+131kHz Signal
• Pulsed or Continuous Output Signal
• Three Signal Application Techniques:
  Direct Connection / Wraparound / Induction
• No periodic Calibration required
• In-built Accessory Tray

Specification

Product name
SGA4 Signal Generator

Part No.
SGA4

Controls
All operation is by push button control as follows:

• On/Off
• Power Level: 2 available power levels via High and Low Power buttons
• Pulse/Continuous Output: toggles between pulse or continuous output using one push button
• Audio/Mute: toggles between loud or muted audio output using one push button

Audio Indications

• Audio Feedback on button push
• Audio pitch drops with increasing load current in Connected Mode
• Audio pitch changes with power level in Induced Mode
• Audio output pulses to indicate Pulsed Mode
• Low battery indicated by interrupted Audio and output signal

Output

• Induced = 32.768kHz
• Connected = 131.072kHz and 32.768kHz
• Carrier Pulse Frequency: 7.5Hz (pulsed mode)

Connected Mode
Connection Mode automatically selected when lead is plugged into socket

Maximum Output Voltage (open circuit)
28V rms

Maximum Output Current (short circuit)
65mA rms

Maximum Power
1W into 400Ω load

Construction

• Case moulded from high impact plastic
• Designed to withstand 1m (3’3”) drop onto a hard surface
• Incorporates clip on accessory storage compartment

Weight (including batteries, Connection Leads and Earth Stake)
3.4kg (7 lb 7 oz)

Dimensions (with Accessory Tray fitted)
360mm x 180mm x 230mm (14.1” x 7” x 9”)

Battery Type
Internal 4 x ‘D’ (LR20) cells (either alkaline non-rechargeable or NiMH rechargeable)

Battery Life
up to 40 hours intermittent use at 20ºC (68ºF) using alkaline cells

IP Rating
65

Notes:
Performance figures stated can be affected by site parameters such as ground conditions, temperature, and strong electromagnetic fields. Specification may be subject to change. All C.Scope Signal Generators are in compliance with the essential requirements and other relevant provisions of Council Directive 2014/53/EU (EMC). Compliance has been demonstrated by testing representative samples to the harmonised standards EN300-330 and EN301-489. The essential radio test suites have been carried out and the equipment is in conformity with all applicable directives. All C.Scope Signal Generators comply with the essential requirements and other provisions of Council Directive 2011/65/EU (RoHS).

* No Periodic Calibration. The SGA4 does not require periodic recalibration. C.Scope authorised Service Centres are also able to provide third-party Test and Calibration Certification should you require it to comply with client or internal regulations.

** Three Year warranty. Conditions apply.

*** Batteries. 4 x D LR20 Alkaline or NiMH Rechargeable batteries housed in a secure battery compartment.

**** In-Built Accessory Tray includes Direct Connection Lead, Auxiliary 10m Earth Lead, Connection Magnets, Earth Stake and Instruction Manual.