DESCRIPTION
Torque meter PCE-DFG N 100TW
Torque meter up to 100 Nm / External torque transducer 1/2″ internal square / Graphic display / PEAK function / Sampling rate max. 1600 Hz / Incl. Software
The torque wrench tester consists of a handheld measuring device and an external torque transducer. The torsion transducer is connected to the hand-held device via a 1.5 m / 4.9 ft long cable and thus enables installation in a test stand or direct assembly on a test bench.
The torque measuring device is delivered adjusted so that the control measurements can be started immediately. A calibration certificate is optionally available for the torque measuring device. This certificate is a target / actual comparison on a traceable reference standard and thus serves as proof of the measurement accuracy. The measurement uncertainty of the torque measuring device is only 0.5% of the measuring range. The torque measuring device is therefore used as a reference device for testing and adjusting static torque tools. A screw latch is essential for dynamic torques.
The torque transducer has a 1/2″ square socket and can perform the torsion measurements in both directions of rotation. With a sampling rate of 1600 Hz, the torque meter reliably detects the first and the maximum torsional moment peak (PEAK). The release moment (” click “) is shown separately in the display and can be deleted either manually or automatically after a set time has elapsed. Thanks to freely adjustable alarm values, the torque measuring device can warn the tester of overload of the torque tool if it does not trigger itself. For a more detailed analysis of the torsional forces, the PC software included in the scope of delivery can be used.
HIGHLIGHTS
– Left / right torsion measurement
– 1600 Hz sampling rate
– Error limit 0.5% of the measuring range
– PEAK / Hold function
– Graphic display
– PC software
– Power adapter and battery operation possible
– 1600 Hz sampling rate
– Error limit 0.5% of the measuring range
– PEAK / Hold function
– Graphic display
– PC software
– Power adapter and battery operation possible
SPECIFICATION
Measuring range | 0 … 100 Nm / 73.76 ft-lb |
Resolution | 0.1 Nm / 0.0738 ft-lb |
Accuracy | ± 0.5% of the measuring range |
Units of measurement | Nm, lbfft, kgfm |
Torque sensor mount | 1/2″ (12.5 x 12.5 mm) internal square |
Torsion measurement | Left / Right |
Display | 2.8″ TFT graphic display |
Alarm modes | Inside Outside |
Sampling rate | 6 … 1600 Hz |
Storage | For 100 measurement series with 8,000 measurement points each |
Power supply | NiMh battery, 6V / 1600-mAh |
Battery life | About 10 hours |
Power supply / charging adapter | 12V / 1 A |
Outputs | Interface: USB Switching output: 12V / 50-mA |
Protection class | IP 54 |
Operating and storage conditions | -10 … 50°C / 14 … 122°F 5 … 95% RH non-condensing |
Torque transducer dimensions | H 85 mm / Ø 72 mm / Ø 104 mm (H 3.3 in / Ø 2.8 in / Ø 4.1 in) (see technical drawing) |
Sensor cable length / td> | Approx. 1.5 m / 4.9 ft |
Dimensions handset | 200 x 97 x 42 mm / 7.9 x 3.8 x 1.7 in |
Weight handset | 540 g / 1.2 lbs |
Weight of the torsion transducer | 985 g / 2.2 lbs |
DELIVERY SCOPE
1 x Torque meter PCE-DFG N 100TW
1 x Torque transducer 100 Nm
1 x 1.5 m / 4.9 ft sensor cable
1 x PC software
1 x USB data cable
1 x Power supply
1 x Carrying case
1 x Sensor screw socket
1 x Instruction manual
1 x Torque transducer 100 Nm
1 x 1.5 m / 4.9 ft sensor cable
1 x PC software
1 x USB data cable
1 x Power supply
1 x Carrying case
1 x Sensor screw socket
1 x Instruction manual
There are no reviews yet.